In this modern era, it’s becoming more and more common to use electrical appliances for ease and comfort. And if you need quick help to fix your clothes, Conair Steamer is a must-have product for you.
But it gets frustrating when suddenly you find your Conair Steamer not working!
Conair Steamer can malfunction due to a variety of reasons. Mineral deposits clogging the steamer, burnt fuse, and empty water reservoir are a few of them.
But no worries. These problems are easily solvable with some simple troubleshooting steps.
More Troubleshooting Guides
Now, do you want to know how to solve the issue of your Conair Steamer not working? Then rest assured! Because in this article, I have discussed everything you need to know to fix your gadget.
So come along, and let’s jump right in!
Reasons Behind Conair Steamer Not Working and Troubleshooting
A number of reasons can be responsible for the malfunctioning of your Conair Steamer. In this segment, I have listed all the causes why your steamer can stop working, with their solutions.
So, if you go through this section thoroughly, you might be able to find a solution to your problem.
So why wait? Let’s get started!
Cause 1: Steamer Clogged with Mineral Deposits
When your Conair Steamer is clogged with mineral deposits, it won’t be able to produce any steam, or will only produce intermittent steam.
Ideally, you should use distilled water in the steamer, as it is pure and clear of minerals.
As we generally use tap water in the steamer, the steamer can get clogged by the minerals in the tap water over time.
Sometimes, these minerals can create clusters and block the steamer. This results in the steamer producing no steam or producing intermittent steam only.
To clean up the minerals, just turn the machine off and let it cool down completely.
After that make a mixture with two cups of distilled water and one cup of vinegar.
Then just dip the machine in the mixture. The minerals will dissolve in the solution.
Then dry the parts with a paper towel, and it should be all clear of minerals.
And that’s it! Your Conair Steamer should start working just as it did before!
Cause 2: Empty or Dirty Water Reservoir
If the water reservoir is dirty, then your steamer may not work properly, or even stop working completely. The problem can also arise if the water reservoir is clean but empty.
If the water reservoir is dirty or empty, it can cause your steamer to produce very little to no steam at all.
If you have been using your Conair Steamer very often, then it is obvious that it will run out of water very quickly. Also, using it regularly will cause dust and dirt accumulation.
So, to keep your steamer free of dust, you will need to decalcify it. The process of cleaning is a bit long, but you don’t need to stress. I have discussed the cleaning process in detail in this article, to stay till the end!
And if your steamer is not producing any steam, the water reservoir doesn’t have enough water to produce it. So, check it, and make sure it’s not empty. Just fill the reservoir with water and it’ll be fine.
Also, check the orientation of the reservoir. Water can get blocked if the orientation is not right. In that case, just fix it, and you should be good to go!
Cause 3: Burnt or Blown-Up Fuse
Sometimes, the core of the problem is a blown-up or burnt fuse. Like every other electronic gadget, Conair Steamer will stop working if the fuse is blown, as it won’t get any power.
This happens very often if the power supply is too much for the system.
This problem is very easily fixable. Firstly, check the power system, and see if there’s any burnt smell or damage in there.
If the fuse has been blown up and the plug is destroyed completely, then you can no longer repair it. In that case, you need to replace it entirely. And that should solve the problem.
Most often though, the plug is not destroyed completely. In that case, check if the prongs are bent. If they are, then just try to straighten it and see if that solves the issue.
Cause 4: Steam Hose Has Problem
Your Conair Steamer can stop working if there’s some issue with the steam hose. If you are not using the steamer properly, the steam hose inside the machine can get bent. As a result, the flow of water stops, and the steamer can’t work.
Most of the time, this causes the steamer to make a gurgling noise.
If the steamer hose is bent, you have to make sure that it’s not bent any longer. Just locate the tube, and check if everything’s alright or not.
If you’ve done it right, your steamer should be working again, as there is no hindrance to water anymore.
And from next time, try to use your steamer carefully so that the hose remains straight in line with the steamer.
Cause 5: Steamer Not Given Adequate Time to Produce Steam
Conair Steamer takes some time to start working and produce steam. It usually takes about 45-60 seconds to start producing steam.
But when you turn off the steamer before it starts working, then you might think there’s something wrong. It’s very common when people use it for the first time.
The solution is pretty straightforward. You just have to give it some time.
Often a new steamer takes a longer time than usual before starting to work. But no need to panic. Just press the steam trigger as long as it takes to produce steam. And if your steamer is okay, this should solve the issue.
Confused On How to Use Your Conair Steamer In The Right Way?
It’s always better to use your steamer carefully than to have to fix it over and over again.
If you know how to use your Conair Steamer in the right way, then you will be less likely to deal with problems in the future.
Here are some simple steps on how to use Conair Steamer:
- Firstly, you will need to fill the water container with cold water. Usually, you will find it at the base.
- Then, replace the container.
- Plug in your Conair Steamer.
- Turn the steamer on.
- Give it some time to heat up. In about 1-2 minutes, steam will start to produce.
- Then, hang your clothing item on a hanger or pant clipper.
- Then keep the nozzle as the lower part of the cloth, then work your way up.
- Keep doing this until your clothes are free of any wrinkles!
How To Clean Conair Your Steamer?
As this machine is used to make your fabric wrinkle-free, sometimes dust can get accumulated in it very easily. But it’s very easy to clean it.
Here’s how you can keep your Conair Steamer all clear and clean:
- Fill your water tank with distilled water, then add vinegar to it. The ratio of distilled water and vinegar should be around 2:1.
- Turn your steamer on and give it some time to heat up.
- Use the steamer until the tank is half empty.
- You should not use this steam on your clothes, as vinegar can damage them. You can use the steam to clean kitchen counters, bathtubs, and anything that doesn’t get damaged by vinegar.
- Then, turn your steamer off and unplug it.
- When the mixture has cooled down, empty the tank by pulling the drain plug at the bottom.
- Repeat the entire process two or three times.
- To make sure that your steamer is free of vinegar, just fill the tank with distilled water, then let the steamer warm up until the tank is almost empty. Then unplug it, and let it cool down.
And that’s about it! Your steamer is all clean as new and free of dirt!
Conclusion
So, as you can see, it’s pretty easy to fix the Conair Steamer not working issue. You just have to be patient and do the right things, and your gadget should be working again!
But if you still can’t solve the problem, then probably it’s time to bid goodbye to your steamer.
At least now you know what to do if you encounter any of these problems in the future. So be aware, and try to solve any issues as soon as you can.
So good luck!