Before calling a technician or replacing the incredibly expensive washer, there are a few things you might want to try with your Maytag Centennial Washer if it’s having problems.
In this Maytag Centennial washer troubleshooting guide, we’ll look at the things you should check, easy solutions to try, and some practical tips when it comes to fixing washers of this type.
Maytag Centennial Washer Troubleshooting
Alright, so here we go:
Maytag Centennial Washer Not Starting
Is your Maytag Centennial washer not starting? several actions you can take to try and troubleshoot the issue.
First, ensure the washer is plugged in and that the socket it is plugged into is operational before doing anything else.
Next, check the door latch to ensure that it’s engaging and that the door is closed properly.
If those things are all good, then the problem may be with the washing machine itself. Try resetting it by unplugging it for 30 seconds and then plugging it back in.
If that doesn’t work, you may need to call a repairman.
Maytag Centennial Washer Stuck on Sensing
Maytag Centennial washing machine is stuck on sensing? Then you can try a few other things to revive it.
First, check to ensure that the water supply valves are turned all the way on.
Next, unplug the washer and plug it back in again.
If that doesn’t work, try resetting the washer by pushing and holding the start/pause button for five seconds.
Finally, if none of these solutions work, you may need to call a repairman.
Maytag Centennial Washer Spin Problems
Do you have spin issues with your Maytag Centennial washer? Several approaches can be used to restart it.
First, make sure that the washer is level. If it’s not level, it can cause the washer to vibrate and not spin properly.
Also, check to see if anything is blocking the washer’s lid from closing. If something is blocking the lid from closing, it could prevent the washer from spinning.
Finally, if none of these solutions work, you may need to call a repairman to take a look at your washer.
Maytag Centennial Washer Reset
The Maytag Centennial washer is a top-loading washing machine that offers a variety of features for an affordable price.
One of the most convenient features of this washer is the reset button, which can be used to restart the cycle if it is interrupted for any reason.
If your Maytag Centennial washer stops mid-cycle, simply press the reset button, and the cycle will continue from where it left off.
This can be a lifesaver if you have a power outage or your washer is accidentally unplugged.
Maytag Centennial Washer Manual
If you need a Maytag Centennial washer manual, you can find it online or in some appliance stores. This manual will help you understand how to operate your washer and troubleshoot any problems that may arise. It is important to read your manual carefully before using your washer so that you can be sure to properly care for your clothes and avoid any damage to the machine.
How to Understand Maytag Centennial Washer Error Codes
You have to figure out the order in which the lights blink because it has to do with the numbers and letters in the error code:
The letter is indicated by the green light blinking ON and OFF, and the error number is indicated by the light that is still on.
When you turn the dial, you will always see the “sensing green” light, possibly followed by other lights.
As the detecting light goes out, the other lights can stay on.
In general, you should now read the lights as follows:
- Greenlight detection equals the letter F.
- The letter E is represented by detecting an OFF light.
Please be aware that the first section of the error code (the “Fill” or “Sensing” or “Soak” lights) will always start with the letter “F,” whereas the second part (the “E”) will not use any of those lights.
Maytag Centennial washer error codes
If your Maytag Centennial washing machine is displaying an error code, it could be indicative of a problem that needs to be addressed. Here is a list of the most common error codes and what they mean:
F0E2: Too much suds
- Clean suds in a basket
- Check the pressure hose and use HE detergent.
F0E4: Rinse with hot water
- The lines for the water supply may be in reverse, so change them.
- Maybe a bad temperature thermistor (and a replacement may be needed).
F0E5: Unbalanced load
- Redistribute clothing—The laundry may not have been correctly sorted in the washing machine.
Suspension rods should be examined. - Washing machine level.
F1E1: Control Error
- Control board detects a fatal failure; perform additional testing.
F1E2: Motor control issue
- Verify the motor’s connections and wiring.
F2E1: The control key is stuck.
- Check to see whether any keys are pressed in or stuck; if so, remove them.
F2E3: Inconsistent board
- Replace it with the proper model of the control board.
F3E1: Pressure system error
- Inspect the switch to the tub hose for damage, kinks, and air leaks.
F3E2: Problem with Inlet Water Temperature
Inspect and replace your temperature sensor as required if you think it might be the cause of this.
F5E1: Door switch fault
- Replace the door switch or reinstall the strike/lock bezel.
F5E3: Inability to unlock the door
- Look for any barriers and get rid of them (also try to unlock it manually from underneath).
F7E1: Basket speed issue
- Reset the washer’s calibration.
- Inspect the motor for a lock.
- Examine the wiring, splutch, belt, capacitor, shifter, and harness (it could be loose).
F7E5: Mode shifter issue
- Either examine the connectors or change the complete unit.
F7E6: Motor problem
- Inspect the motor for physical flaws (use a multimeter to test it; replace it if defective).
- Additionally, it’s possible that energy isn’t reaching it, so remember to check the connectors.
- This is also caused by capacitors, so examine them (the one below, close to the motor, may be defective and not jolting the motor with energy when it should help it start) and change them, if necessary (these capacitors are incredibly inexpensive!). Inspect the wire harness as well.
F7E7: Failure of the Motor’s RPM
- Look for obstacles.
- Check the capacitor and the motor.
- Adjust clothing.
F8E1: Long fill or no
- Inspect the water supply (for pressure).
- Check valve filter coverings for rust or obstruction.
- Examine and change the fill valves (if necessary).
F8E3: Overflow condition
- Check the drain pump and hose for issues.
- Test the pressure sensor.
F8E5: Reversed hot/cold
- Water supply lines may be switched or reversed.
- Examine the temperature thermistor (and replace it if necessary).
F9E1: Long or no drain
- Check for blockages in the drain pump or hose.
- Verify the drain hose (ensure it is not sitting too far in the drain).
- Test the pressure sensor.
SUD: This code stands for “suds detected.”
- It usually occurs when too much detergent has been used or if there is something blocking the washer’s detergent dispenser.
- To remove any suds buildup, simply run a new cycle with no detergent.
dL: This code indicates that there was an issue during the last wash cycle.
- Try running a new cycle and pay close attention to see if anything unusual happens. If you continue to see this error, it may be time to call a repair technician.
Frequently asked questions
Why Won’t My Maytag Washer Start a Cycle?
You can inspect a few factors to identify the problem if your Maytag washer won’t start a cycle.
Firstly, make sure the washer is connected and the power outlet is operational.
Next, make sure the washer is getting power by checking the circuit breaker or fuse box.
If everything appears to be working properly with the power, then it’s time to check the washing machine itself. One possible reason why your Maytag washer won’t start a cycle is that the lid switch is not engaged. The lid switch prevents the washer from starting if the lid is open, so make sure that the lid is closed before trying to start a cycle.
Another possibility is that there is something blocking the door of the washer. Check that nothing is preventing the door from closing completely so that it can latch shut. You may have to call a technician if, after checking all of these options, your Maytag washer still won’t start a cycle.
Why Won’t My Maytag Washer Drain and Spin?
There are a few things you can check to figure out why your Maytag washer won’t drain.
First, confirm that the washer is plugged in as well as the circuit breaker is not blown.
Next, check the drain hose to make sure it is not kinked or clogged.
If the hose appears to be clear, try removing it and running water through it to see if there is a blockage further down the line.
If neither of these solutions solves the problem, your next step should be to check the washing machine’s pump. The pump may be broken or clogged, preventing it from draining properly. To access the pump, you will need to remove the back panel of your washer.
Once you have done so, inspect the pump for any damage or debris that could be causing a blockage. If you find anything, clean it out and see if that fixes the issue.
After testing each of these items, if your washer still won’t drain and spin, you may have to call a technician. There could be an issue with one of the internal components of your washer that is beyond your scope of knowledge or expertise to fix. In any case, a professional will be able to diagnose and solve the problem quickly so that you can get back to doing laundry as usual!
How Do You Reset the Sensor on a Maytag Washer?
If your Maytag washer is not draining properly, you may need to reset the sensor. To do this,
First, unplug the washer from the power outlet. Then, locate the drain pump filter on the front of the washer and remove it. Clean out any debris that may be blocking the filter.
Next, locate the drain hose on the back of the washer and disconnect it from the machine. Again, check for any blockages and remove them.
Finally, reconnect both the drain hose and pump filter and plug in your washer. Run a test cycle to see if it is draining properly.
If not, you may need to call a technician for further assistance.
How Do I Reset My Maytag Centennial Washing Machine?
If your Maytag Centennial washing machine isn’t working properly, you may need to reset it.
To do this, unplug the machine and plug it back in. Then, press and hold the “Start/Pause” button for five seconds.
This should reset the machine. If it doesn’t work, you may need to call a technician.
Conclusion
Resetting the machine is the easiest method to begin troubleshooting your Maytag Centennial washer.
If it doesn’t work, try running a self-diagnosis on your washer and resolving any fault codes as previously mentioned.
These two methods are typically used to solve the majority of basic Maytag Centennial washer problems.
I wish you luck as you troubleshoot.
Are you a Whirlpool Duet Washer user? Facing any problems with your washer? Then read Whirlpool Duet Washer Troubleshooting now.