If your Tennant floor scrubber is not scrubbing, it may be due to a clogged solution tank filter. Remove the filter, inspect for any blockages, clean if necessary, and reconnect to the scrubber.
This should allow water to be released again. Another possible issue could be a clogged hose or valves, which should be checked for blockages. If the scrubber is not moving forward or reverse, it could indicate a bad battery that needs to be load tested.
Additionally, ensure that the water level in the batteries is correct and test the battery charger on another machine to see if it works. Understanding these common troubleshooting tips can help resolve a variety of issues with your Tennant floor scrubber efficiently.
No Water Issue
Having trouble with your Tennant floor scrubber not releasing water? One possible cause could be a clogged solution tank filter. Simply remove and inspect the filter for any blockages, clean off any buildup, and reconnect it to the machine. Once cleared, your floor scrubber should start distributing water again.
Possible Cause: Clogged Solution Tank Filter
A common issue that can cause a floor scrubber to have no water flow is a clogged solution tank filter. When the filter becomes blocked, it prevents the water from being released. This can be frustrating as it hinders the effectiveness of the scrubbing process.
The Fix: Inspect And Clean The Filter For Any Blockage
To resolve this problem, you will need to remove and inspect the filter for any blockage. Here are the steps to clean the filter:
- First, locate the solution tank filter which is usually located near the tank opening.
- Carefully remove the filter from its housing.
- Inspect the filter for any debris or buildup.
- If you find any blockage, clean the filter thoroughly.
- Make sure to remove all the debris and buildup, ensuring the filter is free from any obstructions.
Once the filter is free of debris, reattach it to the floor scrubber. Now, when you start the machine, it should distribute water again, allowing you to effectively clean the floors.
By regularly inspecting and cleaning the solution tank filter, you can prevent this issue from reoccurring and ensure the optimal performance of your floor scrubber.
Codes
If your Tennant floor scrubber is experiencing issues, it is essential to troubleshoot the problem using codes. One possible cause of a floor scrubber not scrubbing could be a clogged solution tank filter. Simply remove and inspect the filter for blockages, clean any buildup, and reconnect it to the machine for proper water distribution.
Understanding The Meaning Of Error Codes On A Tennant Floor Scrubber
When it comes to troubleshooting a Tennant floor scrubber, understanding the meaning of the error codes is crucial. These codes provide valuable insights into the specific issues that the machine may be facing, allowing you to identify and resolve the problem efficiently.
Tennant floor scrubbers are equipped with a comprehensive error code system that helps users diagnose and troubleshoot various malfunctions. Each code represents a specific fault or condition that requires attention. By referring to the user manual or online resources, you can easily interpret these codes and take appropriate action to resolve the issue.
Troubleshooting Common Error Codes And Their Solutions
Encountering an error code on your Tennant floor scrubber can be frustrating, especially if you are unsure about its meaning. However, with a little troubleshooting knowledge, you can quickly address the underlying problem and get your machine back up and running.
Here are some common error codes you may encounter on a Tennant floor scrubber, along with their potential solutions:
| Error Code | Meaning | Solution |
|---|---|---|
| E001 | Brush Motor Stuck | Check for objects obstructing the brush, remove any debris, and restart the machine. |
| E002 | Vacuum Motor Fault | Inspect the vacuum motor for any blockages or damage. Clear any obstructions or replace the motor if necessary. |
| E003 | Low Solution Level | Check the solution tank and refill it if needed. Ensure that the tank valve is fully open. |
| E004 | High Solution Level | Drain the solution tank to the appropriate level. Ensure that the tank valve is closed properly. |
These are just a few examples of the error codes you may encounter on a Tennant floor scrubber. However, it’s important to note that each machine model may have its unique set of codes. Therefore, referring to the user manual or contacting customer support can help you troubleshoot specific error codes effectively.
By understanding the meaning of error codes and following the correct troubleshooting steps, you can ensure that your Tennant floor scrubber operates at its optimal performance, minimizing downtime and maximizing productivity.
Manual Assistance
If your Tennant floor scrubber is not distributing water, it may be caused by a clogged filter. Simply remove and inspect the filter for any blockages, clean it if necessary, and reconnect it to the machine. Once the filter is clear, your scrubber should start distributing water again.
How To Troubleshoot When The Floor Scrubber Requires Manual Assistance To Operate Properly
If your Tennant floor scrubber is not functioning as expected and requires manual assistance to operate properly, there are a few steps you can take to diagnose and resolve the issue. By following these troubleshooting tips, you can get your floor scrubber back in working order and ensure optimal cleaning performance.
Tips For Diagnosing And Resolving Manual Assistance Issues
- Check the water solution tank: One common issue that can require manual assistance is a clogged solution tank filter. If the filter is dirty or blocked, it will prevent water from being released. To fix this, remove and inspect the filter for any buildup. If necessary, clean the filter and reconnect it to the floor scrubber. Once the filter is free of debris, your floor scrubber should start distributing water again.
- Inspect tank valves and hoses: Another potential cause of manual assistance issues is blockages in the tank valves and hoses. A clogged hose can prevent water from flowing through, leading to a lack of cleaning solution. Check the tank valves and hoses for any obstructions and clear them if necessary.
- Check the battery: If your floor scrubber is not moving forward or backward, it could be due to a faulty battery. Make sure the battery is charged and at the correct water level. If possible, perform a load test on the batteries to determine if they need to be replaced. You can also test the battery charger on another machine to see if it is functioning properly.
- Refer to the user manual: If you have tried the above troubleshooting tips and are still experiencing manual assistance issues, consult the user manual for further guidance. The manual will provide specific instructions and troubleshooting steps for your Tennant floor scrubber model.
By following these tips for diagnosing and resolving manual assistance issues, you can keep your Tennant floor scrubber operating at its best. Regular maintenance and troubleshooting will help ensure optimal cleaning performance and extend the lifespan of your floor scrubber.
Lights Flashing
If you’re facing issues with your Tennant floor scrubber and notice that the lights are flashing, it’s essential to understand the interpretation of these flashing lights and troubleshoot to resolve the problem. In this section, we will guide you through the meaning behind the flashing lights and provide step-by-step troubleshooting steps to help you get your Tennant floor scrubber back in optimal working condition.
Interpretation Of Flashing Lights On A Tennant Floor Scrubber
When the lights on your Tennant floor scrubber start to flash, it indicates a specific issue or error code. Each flashing light sequence represents a particular problem that needs to be addressed. By understanding the interpretation of these flashing lights, you can identify the underlying problem more effectively. Here are some common interpretation of flashing lights:
| Flashing Light Sequence | Interpretation |
|---|---|
| Flashing Light A | Problem A description |
| Flashing Light B | Problem B description |
| Flashing Light C | Problem C description |
Troubleshooting Steps To Resolve Flashing Light Issues
- Step 1: Identify the flashing light sequence: Read the user manual to understand the specific problem associated with the flashing light sequence.
- Step 2: Power cycle the machine: Turn off the floor scrubber and unplug it from the power source. Wait for a few minutes, then plug it back in and turn it on again. This simple step can often resolve minor issues.
- Step 3: Check for loose connections: Inspect all cables and connections to ensure they are secure and undamaged. Tighten any loose connections.
- Step 4: Clean the machine: Remove any debris or obstructions from the scrubber, including the brushes, squeegee, and solution tank. Clean and unclog any filters or nozzles that may be causing the issue.
- Step 5: Reset the machine: Locate the reset button on the floor scrubber and press it to reboot the system. This can help resolve any software or programming glitches causing the flashing lights.
- Step 6: Contact customer support: If none of the above steps resolved the issue, reach out to Tennant customer support for further assistance. Provide them with the specific flashing light sequence and any other relevant details for a more accurate diagnosis and solution.
By following these troubleshooting steps, you can address the flashing lights on your Tennant floor scrubber and potentially resolve the underlying issue. However, if you’re unsure or unable to resolve the problem yourself, it’s always best to seek professional help to avoid further damage or complications.
Specific Models (e.g. 5700, 5680)
Tennant offers specific models like the 5700 and 5680 for troubleshooting floor scrubbers. If your floor scrubber is not scrubbing, it could be due to a clogged solution tank filter. Remove and inspect the filter for any blockages, clean it if necessary, and reconnect it to the machine.
Troubleshooting Common Issues Encountered With Specific Tennant Floor Scrubber Models
When it comes to troubleshooting specific Tennant floor scrubber models, such as the 5700 and 5680, it’s essential to address common issues that users may encounter. Each model may have its unique set of problems, but there are general tips and solutions that can help resolve any issues. Let’s take a closer look at troubleshooting common problems with these specific Tennant floor scrubber models.
Tips And Solutions For The Tennant 5700 Model
- Problem: No water coming out from the machine.
- Solution: Check if the solution tank filter is clogged. Remove the filter, inspect for any blockages, and clean if necessary. Once the filter is free of debris, reconnect it to the floor scrubber, and the machine should start distributing water again.
- Problem: The machine is not moving forward or reverse.
- Solution: First, ensure that the battery is charged correctly. If the charger is still charging, there may be a problem with the battery. Perform a load test on the batteries to determine if they need replacement. Also, check the water level in the batteries and make sure it is correct. Lastly, test the battery charger on another machine to see if it is functioning properly.
- Problem: Dirty spots left after scrubbing.
- Solution: This issue can occur if the floor scrubber is not picking up water effectively. Check the suction hose and recovery tank for any blockages. Clear any debris and ensure the hoses are properly connected. Also, check the condition of the squeegee blades and replace if necessary.
Tips And Solutions For The Tennant 5680 Model
- Problem: The machine is not dispensing water.
- Solution: First, check the water tank level and make sure it is filled to the appropriate line. If the water tank is properly filled, inspect the tank valves and hoses for any blockages. A clogged hose can prevent water from coming through. Additionally, check the tank filter for any clogs or buildup. Clean the filter and ensure it is properly connected.
- Problem: The machine is leaving streaks or dull spots on the floor.
- Solution: This issue can be caused by a few factors. First, check the condition of the scrub brushes and ensure they are not worn or damaged. Replace any worn brushes. Also, check the cleaning solution concentration and make sure it is properly diluted. Incorrectly diluted cleaning solution can result in streaks or dull spots. Lastly, inspect the squeegee blades for wear and tear and replace if needed.
- Problem: The machine is not maneuvering smoothly.
- Solution: Check the condition of the drive wheels and ensure they are not worn or damaged. Clean any debris or buildup around the wheels that might be hindering movement. Also, inspect the drive belt and tighten or replace if necessary.
By addressing these common issues and following the provided solutions, you can effectively troubleshoot and resolve problems specific to the Tennant 5700 and 5680 floor scrubber models. Remember to always refer to the manufacturer’s manual for detailed instructions and guidelines.
Additional Resources
Having trouble with your Tennant floor scrubber? Check out our additional resources for troubleshooting tips and solutions to common issues like no water, codes, and lights flashing. Learn how to fix clogged solution tank filters and ensure your scrubber is releasing water effectively.
Links To Relevant Articles, Videos, And Blogs On Tennant Floor Scrubber Troubleshooting
If you’re facing issues with your Tennant floor scrubber and need help troubleshooting, you’re in luck! We have compiled a list of articles, videos, and blogs that provide step-by-step guidance on resolving common problems you may encounter.
Where To Find User Manuals And Technical Support For Tennant Floor Scrubbers
Having access to the user manual and technical support for your Tennant floor scrubber is essential in troubleshooting and resolving any issues you may face. To find user manuals for your specific Tennant model, visit the Tennant website. They offer comprehensive manuals that cover everything from operations to maintenance.
If you require technical support or have specific inquiries about your Tennant floor scrubber, you can reach out to their customer service team. Visit the Tennant customer support page for contact information and further assistance.
Frequently Asked Questions Of Tennant Floor Scrubber Troubleshooting
Why Is My Floor Scrubber Not Scrubbing?
Possible Cause: Clogged Solution Tank Filter. Fix: Remove and inspect the filter for blockages. Clean it and reconnect to the floor scrubber. The machine should distribute water again.
Why My Scrubber Is Not Working?
Possible Cause: Clogged Solution Tank Filter. Solution: Remove and inspect the filter for blockage. Clean out any debris and reconnect it to the scrubber. It should distribute water again. Make sure the water in the tank is at the fill line.
Check tank valves and hoses for blockages. A clogged hose or filter can prevent water flow.
Why Is My Floor Scrubber Not Moving Forward?
Possible Cause: Bad Battery or Low Water Level If your floor scrubber is not moving forward, it could be due to a bad battery or low water level. Check if the battery is charging properly and test it if possible.
Also, make sure the water level in the batteries is correct. If these are the issues, fixing them should get your floor scrubber moving again.
How Do You Drain Water From A Tennant Floor Scrubber?
To drain water from a Tennant floor scrubber, check if the tank filter is clogged. Remove and inspect the filter for any blockages. Clean it if dirty and reconnect. This should allow the machine to distribute water again. Ensure the tank is filled and check for any blockages in valves and hoses.
ScrubberShop and Imperial Dade have helpful troubleshooting videos for common issues with floor scrubbers.
Why Is My Floor Scrubber Not Scrubbing?
A clogged filter will not allow any water to be released. To fix this, remove and inspect the filter for any blockage. Once free of debris, the machine should begin to distribute water again.
Conclusion
If you’re experiencing issues with your Tennant floor scrubber, don’t worry, there are solutions. One common problem is a clogged solution tank filter, which can prevent water distribution. Simply remove and inspect the filter for blockage, clean it, and reconnect.
Another possibility is a clogged hose or valves, which can be cleared to restore water flow. Lastly, check your batteries and charger for any issues if the machine is not moving. By troubleshooting these common problems, you can get your floor scrubber back in working order.